CEN TC 132 , استانداردهای آلومینیوم و آلیاژ آلومینیوم

دانلود استانداردهای BS EN ISO

CEN TC 132  : Aluminium And Aluminium Alloys

دانلود استانداردهای اروپا_ EN برای متریال آلومینیوم و آلومینیوم آلیاژی
(پکیج استانداردهای کمیته فنی CEN TC 132)

لیست استاندارد و ویرایش های این مجموعه:

 

  1. EN 485-1 – 2016 __ Aluminium and aluminium alloys – Sheet, strip and plate – Part 1: Technical conditions for inspection and delivery
  2. EN 485-2 – 2016+A1-2018 __ Aluminium and aluminium alloys – Sheet, strip and plate – Part 2: Mechanical properties
  3. EN 485-3 – 2003 __ Aluminium and aluminium alloys – Sheet, strip and plate – Part 3: Tolerances on dimensions and form for hot-rolled products
  4. EN 485-4 – 1993 __ Aluminium and aluminium alloys – Sheet, strip and plate – Part 4: Tolerances on shape and dimensions for cold-rolled products
  5. EN 486 – 2009 Aluminium and aluminium alloys – Extrusion ingots – Specifications
  6. EN 487 – 2009 Aluminium and aluminium alloys – Rolling ingots – Specifications
  7. EN 515 – 2017 Aluminium and aluminium alloys – Wrought products – Temper designations
  8. EN 541 – 2006 Aluminium and aluminium alloys – Rolled products for cans, closures and lids – Specifications
  9. EN 546-1 – 2006 __ Aluminium and aluminium alloys – Foil – Part 1: Technical conditions for inspection and delivery
  10. EN 546-2 – 2006 __ Aluminium and aluminium alloys – Foil – Part 2: Mechanical properties
  11. EN 546-3 – 2006 __ Aluminium and aluminium alloys – Foil – Part 3: Tolerances on dimensions
  12. EN 546-4 – 2006 __ Aluminium and aluminium alloys – Foil – Part 4: Special property requirements
  13. EN 570 – 2007 Aluminium and aluminium alloys – Impact extrusion slugs obtained from wrought products – Specification
  14. EN 573-1 – 2004 __ Aluminium and aluminium alloys – Chemical composition and form of wrought products – Part 1: Numerical designation system
  15. EN 573-2 – 1994 __ Aluminium and aluminium alloys – Chemical composition and form of wrought products – Part 2: Chemical symbol based designation system
  16. EN 573-3 – 2019 __ Aluminium and aluminium alloys – Chemical composition and form of wrought products – Part 3: Chemical composition and form of products
  17. EN 573-5 – 2007 __ Aluminium and aluminium alloys – Chemical composition and form of wrought products – Part 5: Codification of standardized wrought products
  18. EN 575 – 1995 Aluminium and aluminium alloys – Master alloys produced by melting – Specifications
  19. EN 576 – 2003 Aluminium and aluminium alloys – Unalloyed aluminium ingots for remelting – Specifications
  20. EN 577 – 1995 __ Aluminium and aluminium alloys – Liquid metal – Specifications
  21. EN 586-1 – 1997 __ Aluminium and aluminium alloys – Forgings – Part 1: Technical conditions for inspection and delivery
  22. EN 586-2 – 1994 __ Aluminium and aluminium alloys – Forgings – Part 2: Mechanical properties and additional property requirements
  23. EN 586-3 – 2001 __ Aluminium and aluminium alloys – Forgings – Part 3: Tolerances on dimensions and form
  24. EN 601 – 2004 __ Aluminium and aluminium alloys – Castings – Chemical composition of castings for use in contact with foodstuff
  25. EN 602 – 2004 __ Aluminium and aluminium alloys – Wrought products – Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff
  26. EN 603-1 – 1996 __ Aluminium and aluminium alloys – Wrought forging stock – Part 1: Technical conditions for inspection and delivery
  27. EN 603-2 – 1996 __ Aluminium and aluminium alloys – Wrought forging stock – Part 2: Mechanical properties
  28. EN 603-3 – 2000 __ Aluminium and aluminium alloys – Wrought forging stock – Part 3: Tolerances on dimensions and form
  29. EN 604-1 – 1997 __ Aluminium and aluminium alloys – Cast forging stock – Part 1: Technical conditions for inspection and delivery
  30. EN 604-2 – 1997 __ Aluminium and aluminium alloys – Cast forging stock – Part 2: Tolerances on dimensions and form
  31. EN 683-1 – 2006 __ Aluminium and aluminium alloys – Finstock – Part 1: Technical conditions for inspection and delivery
  32. EN 683-2 – 2006 __ Aluminium and aluminium alloys – Finstock – Part 2: Mechanical properties
  33. EN 683-3 – 2006 __ Aluminium and aluminium alloys – Finstock – Part 3: Tolerances on dimensions and form
  34. EN 754-1 – 2016 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 1: Technical conditions for inspection and delivery
  35. EN 754-2 – 2016 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 2: Mechanical properties
  36. EN 754-3 – 2008 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 3: Round bars, tolerances on dimensions and form
  37. EN 754-4 – 2008 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 4: Square bars, tolerances on dimensions and form
  38. EN 754-5 – 2008 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 5: Rectangular bars, tolerances on dimensions and form
  39. EN 754-6 – 2008 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 6: Hexagonal bars, tolerances on dimensions and form
  40. EN 754-7 – 2016 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 7: Seamless tubes, tolerances on dimensions and form
  41. EN 754-8 – 2016 __ Aluminium and aluminium alloys – Cold drawn rod/bar and tube – Part 8: Porthole tubes, tolerances on dimensions and form
  42. EN 755-1 – 2016 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 1: Technical conditions for inspection and delivery
  43. EN 755-2 – 2016 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 2: Mechanical properties
  44. EN 755-3 – 2008 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 3: Round bars, tolerances on dimensions and form
  45. EN 755-4 – 2008 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 4: Square bars, tolerances on dimensions and form
  46. EN 755-5 – 2008 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 5: Rectangular bars, tolerances on dimensions and form
  47. EN 755-6 – 2008 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 6: Hexagonal bars, tolerances on dimensions and form
  48. EN 755-7 – 2016 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 7: Seamless tubes, tolerances on dimensions and form
  49. EN 755-8 – 2016 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 8: Porthole tubes, tolerances on dimensions and form
  50. EN 755-9 – 2016 __ Aluminium and aluminium alloys – Extruded rod/bar, tube and profiles – Part 9: Profiles, tolerances on dimensions and form
  51. EN 851 – 2014 __ Aluminium and aluminium alloys – Circle and circle stock for the production of culinary utensils – Specifications
  52. EN 941 – 2014 __ Aluminium and aluminium alloys – Circle and circle stock for the production of general applications – Specifications
  53. EN 1301-1 – 2008 __ Aluminium and aluminium alloys – Drawn wire – Part 1: Technical conditions for inspection and delivery
  54. EN 1301-2 – 2008 __ Aluminium and aluminium alloys – Drawn wire – Part 2: Mechanical properties
  55. EN 1301-3 – 2008 __ Aluminium and aluminium alloys – Drawn wire – Part 3: Tolerances on dimensions
  56. EN 1386 – 2007 __ Aluminium and aluminium alloys – Tread plate – Specifications
  57. EN 1396 – 2015 __ Aluminium and aluminium alloys – Coil coated sheet and strip for general applications – Specifications
  58. EN 1559-4 – 2015 __ Founding – Technical conditions of delivery – Part 4: Additional requirements for aluminium alloy castings
  59. EN 1592-1 – 1997 __ Aluminium and aluminium alloys – HF seam welded tubes – Part 1: Technical conditions for inspection and delivery
  60. EN 1592-2 – 1997 __ Aluminium and aluminium alloys – HF seam welded tubes – Part 2: Mechanical properties
  61. EN 1592-3 – 1997 __ Aluminium and aluminium alloys – HF seam welded tubes – Part 3: Tolerances on dimensions and form for circular tubes
  62. EN 1592-4 – 1997 __ Aluminium and aluminium alloys – HF seam welded tubes – Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes
  63. EN 1669 – 1996 __ Aluminium and aluminium alloys – Test methods – Earing test for sheet and strip
  64. EN 1676 – 2020 __ Aluminium and aluminium alloys – Alloyed ingots for remelting – Specifications
  65. EN 1706 – 2020+A1-2021 __ Aluminium and aluminium alloys – Castings – Chemical composition and mechanical properties
  66. EN 1715-1 – 2008 __ Aluminium and aluminium alloys – Drawing stock – Part 1: General requirements and technical conditions for inspection and delivery
  67. EN 1715-2 – 2008 __ Aluminium and aluminium alloys – Drawing stock – Part 2: Specific requirements for electrical applications
  68. EN 1715-3 – 2008 __ Aluminium and aluminium alloys – Drawing stock – Part 3: Specific requirements for mechanical uses (excluding welding)
  69. EN 1715-4 – 2008 __ Aluminium and aluminium alloys – Drawing stock – Part 4: Specific requirements for welding applications
  70. EN 1780-1 – 2002 __ Aluminium and aluminium alloys – Designation of alloyed aluminium ingots for remelting, master alloys and castings – Part 1: Numerical designation system
  71. EN 1780-2 – 2002 __ Aluminium and aluminium alloys – Designation of alloyed aluminium ingots for remelting, master alloys and castings – Part 2: Chemical symbol based designation system
  72. EN 1780-3 – 2002 __ Aluminium and aluminium alloys – Designation of alloyed aluminium ingots for remelting, master alloys and castings – Part 3: Writing rules for chemical composition
  73. EN ISO 2085 – 2018 __ Anodizing of aluminium and its alloys – Check for continuity of thin anodic oxidation coatings – Copper sulfate test (ISO 2085:2018)
  74. EN ISO 2106 – 2011 __ Anodizing of aluminium and its alloys – Determination of mass per unit area (surface density) of anodic oxidation coatings – Gravimetric method (ISO 2106:2019)
  75. EN ISO 2128 – 2010 __ Anodizing of aluminium and its alloys – Determination of thickness of anodic oxidation coatings – Non-destructive measurement by split-beam microscope (ISO 2128:2010)
  76. EN ISO 2143 – 2017 __ Anodizing of aluminium and its alloys – Estimation of loss of absorptive power of anodic oxidation coatings after sealing – Dye-spot test with prior acid treatment (ISO 2143:2017)
  77. EN ISO 2376 – 2010 __ Anodizing of aluminium and its alloys – Determination of breakdown voltage and withstand voltage (ISO 2376:2019)
  78. EN ISO 2931 – 2018 __ Anodizing of aluminium and its alloys – Assessment of quality of sealed anodic oxidation coatings by measurement of admittance (ISO 2931:2017)
  79. EN ISO 3210 – 2017 __ Anodizing of aluminium and its alloys – Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s) (ISO 3210:2017)
  80. EN ISO 3211 – 2010 __ Anodizing of aluminium and its alloys – Assessment of resistance of anodic oxidation coatings to cracking by deformation (ISO 3211:2018)
  81. EN ISO 6581 – 2018 __ Anodizing of aluminium and its alloys – Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings (ISO 6581:2018)
  82. EN ISO 6719 – 2010 __ Anodizing of aluminium and its alloys – Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments (ISO 6719:2010)
  83. EN ISO 7599 – 2018 __ Anodizing of aluminium and its alloys – Method for specifying decorative and protective anodic oxidation coatings on aluminium (ISO 7599:2018)
  84. EN ISO 7668 – 2018 __ Anodizing of aluminium and its alloys – Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85° (ISO 7668:2021)
  85. EN ISO 7759 – 2010 __ Anodizing of aluminium and its alloys – Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO/FDIS 7759:2010)
  86. EN ISO 8251 – 2018 __ Anodizing of aluminium and its alloys – Measurement of abrasion resistance of anodic oxidation coatings (ISO 8251:2018)
  87. EN ISO 8993 – 2010 __ Anodizing of aluminium and its alloys – Rating system for the evaluation of pitting corrosion – Chart method (ISO 8993:2018)
  88. EN ISO 8994 – 2011 __ Anodizing of aluminium and its alloys – Rating system for the evaluation of pitting corrosion – Grid method (ISO 8994:2018)
  89. EN 12392 – 2016+A1-2022 __ Aluminium and aluminium alloys – Wrought products and cast products – Special requirements for products intended for the production of pressure equipment
  90. EN 13195 – 2013 __ Aluminium and aluminium alloys – Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore)
  91. EN 13957 – 2008 __ Aluminium and aluminium alloys – Extruded round, coiled tube for general applications – Specification
  92. EN 13958 – 2008 __ Aluminium and aluminium alloys – Cold drawn, round, coiled tube for general applications – Specification
  93. EN 14121 – 2009 __ Aluminium and aluminium alloys – Sheet, strip and plate for electrotechnical applications
  94. EN 14242 – 2004 __ Aluminium and aluminium alloys – Chemical analysis – Inductively coupled plasma optical emission spectrometric analysis
  95. EN 14286 – 2008 __ Aluminium and aluminium alloys – Weldable rolled products for tanks for the storage and transportation of dangerous goods
  96. EN 14287 – 2004 __ Aluminium and aluminium alloys – Specific requirements on the chemical composition of products intended to be used for the manufacture of packaging and packaging components
  97. EN 14361 – 2004 __ Aluminium and aluminium alloys – Chemical analysis – Sampling from metal melts
  98. EN 14392 – 2007 __ Aluminium and aluminium alloys – Requirements for anodised products for use in contact with foodstuff
  99. EN 14726 – 2019 __ Aluminium and aluminium alloys – Determination of the chemical composition of aluminium and aluminium alloys by spark optical emission spectrometry
  100. EN 15088 – 2005 __ Aluminium and aluminium alloys – Structural products for construction works – Technical conditions for inspection and delivery
  101. CEN/TR 16748 – 2014 __ Aluminium and aluminium alloys – Mechanical potential of Al-Si alloys for high pressure, low pressure and gravity die casting
  102. CEN/TR 16749 – 2014 __ Aluminium and aluminium alloys – Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
  103. EN 16773 – 2016 __ Aluminium and aluminium alloys – Guideline for the production of foil-stock in the field of semi rigid foodstuff containers
  104. EN 16914 – 2017 __ Aluminium and aluminium alloys – Hot-rolled armour plates in weldable aluminium alloy – Technical delivery conditions
  105. EN ISO 10215 – 2018 __ Anodizing of aluminium and its alloys – Visual determination of image clarity of anodic oxidation coatings – Chart scale method (ISO 10215:2018)
  106. EN 12020-1 – 2022 __ Aluminium and aluminium alloys – Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 – Part 1: Technical conditions for inspection and delivery
  107. EN 12020-2 – 2021 __ Aluminium and aluminium alloys – Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 – Part 2: Tolerances on dimensions and form
  108. EN 12258-1 – 2012 __ Aluminium and aluminium alloys – Terms and definitions – Part 1: General terms
  109. EN 12258-2 – 2004 __ Aluminium and aluminium alloys – Terms and definitions – Part 2: Chemical analysis
  110. EN 12258-3 – 2003 __ Aluminium and aluminium alloys – Terms and definitions – Part 3: Scrap
  111. EN 12258-4 – 2004 __ Aluminium and aluminium alloys – Terms and definitions – Part 4: Residues of the aluminium industry
  112. EN 12482-1 – 1998 __ Aluminium and aluminium alloys – Reroll stock for general applications – Part 1: Specifications for hot rolled reroll stock
  113. EN 12482-2 – 1998 __ Aluminium and aluminium alloys – Reroll stock for general applications – Part 2: Specifications for cold rolled reroll stock
  114. EN 13920-1 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 1: General requirements, sampling and tests
  115. EN 13920-10 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 10: Scrap consisting of used aluminium beverage cans
  116. EN 13920-11 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 11: Scrap consisting of aluminium-copper radiators
  117. EN 13920-12 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 12: Turnings consisting of one single alloy
  118. EN 13920-13 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 13: Mixed turnings consisting of two or more alloys
  119. EN 13920-14 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 14: Scrap from post-consumer aluminium packagings
  120. EN 13920-15 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 15: Decoated aluminium scrap from post-consumer aluminium packagings
  121. EN 13920-16 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 16: Scrap consisting of skimmings, drosses, spills and metallics
  122. EN 13920-2 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 2: Unalloyed aluminium scrap
  123. EN 13920-3 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 3: Wire and cable scrap
  124. EN 13920-4 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 4: Scrap consisting of one single wrought alloy
  125. EN 13920-5 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 5: Scrap consisting of two or more wrought alloys of the same series
  126. EN 13920-6 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 6: Scrap consisting of two or more wrought alloys
  127. EN 13920-7 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 7: Scrap consisting of castings
  128. EN 13920-8 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 8: Scrap consisting of non-ferrous materials from shredding processes destined to aluminium separation processes
  129. EN 13920-9 – 2003 __ Aluminium and aluminium alloys – Scrap – Part 9: Scrap from aluminium separation processes of non-ferrous shredded materials
  130. EN 13981-1 – 2003 __ Aluminium and aluminium alloys – Products for structural railway applications – Technical conditions for inspection and delivery – Part 1: Extruded products
  131. EN 13981-2 – 2004 __ Aluminium and aluminium alloys – Products for structural railway applications – Technical conditions for inspection and delivery – Part 2: Plates and sheets
  132. EN 13981-3 – 2006 __ Aluminium and aluminium alloys – Products for structural railway applications – Technical conditions for inspection and delivery – Part 3: Castings
  133. EN 13981-4 – 2006 __ Aluminium and aluminium alloys – Products for structural railway applications – Technical conditions for inspection and delivery – Part 4: Forgings

 

مشخصات فایل
دیدگاه کاربران

دیدگاهتان را بنویسید

دکمه بازگشت به بالا